FlashWrite2 (J2534)

Book Subaru programming session

Subaru. ECM/TCM reprogramming via FlashWrite2, calibration updates, module setup after replacement.

30–90 min · live openings below, evenings by arrangement Your J2534 + Windows laptop Refunded if we can't complete it
Read Auto Module Lab — Remote Programming Session Terms
1. WHO WE ARE AND WHAT THESE TERMS COVER

Auto Module Lab ("AML", "we", "us") is operated by DLP Mobile Services LLC, Arlington, Texas. These Remote Programming Session Terms govern remote module programming, flashing, and coding sessions you purchase from automodulelab.com — work we perform on a vehicle in YOUR custody, through your programming interface and internet connection. The mail-in module services have their own terms; if your order also includes mail-in work or hardware, the terms for those items apply to those items.

2. SCHEDULING

After purchase we contact you to schedule the session during our published hours. Please have the vehicle, interface, and laptop ready at the scheduled time. If you need to reschedule, tell us as early as you can; we reschedule at no charge except where a fee is expressly stated on the session listing.

3. YOUR SETUP — REQUIRED FOR THE SESSION

Remote programming runs entirely through equipment on your side. Before the session you must have: a stable internet connection (wired strongly recommended); a Windows laptop we can reach by the remote-access method we specify; a compatible, supported J2534 or manufacturer-specified interface, firmly connected to the vehicle; a battery maintainer or stable power supply on the vehicle rated for programming (voltage drops during a write are the leading cause of failed flashes); and the vehicle in the condition the session listing calls for. If a session cannot proceed because required setup is missing or not working, we will reschedule it; where repeated attempts fail for the same customer-side reason, a rescheduling fee applies only if one is stated on the session listing.

4. INTERRUPTED-WRITE RISK

Flashing a control module is interruptible only at real risk: a power drop, cable disconnect, laptop sleep, or internet failure DURING a write can leave the module unusable. We use recovery procedures where the platform supports them. If a write is interrupted by a failure on our side, we re-attempt and recover at our cost. If a write is interrupted by a customer-side failure (vehicle power, cable, laptop, or connection), we will attempt recovery where possible, but AML is not responsible for module damage caused by that interruption; bench recovery of a module bricked this way is available as a separate mail-in service.

5. OEM SOFTWARE, SUBSCRIPTIONS, AND PER-VIN FEES

Some manufacturers charge for programming software, subscriptions, or per-VIN calibration files. The session price includes these only where the session listing says so; otherwise the listing states what is included and what the OEM charges separately.

6. SCOPE — THE OPERATION, NOT THE VEHICLE

The session covers the programming, flashing, or coding operation described on the listing. We work through your connection and can only see what the tools show; we cannot verify your vehicle's wiring, grounds, battery health, connectors, other modules, or the diagnosis that led you to book the session. A successfully completed operation does not guarantee an unrelated vehicle symptom is resolved. Where a listing says an operation is supported "where supported" or subject to hardware/firmware verification, that verification is part of the session. This section does not excuse an operation we actually performed defectively — see Section 8.

7. CANCELLATION AND REFUNDS

Before the session is performed: full refund. Session attempted but blocked by missing customer-side setup (Section 3): we reschedule — the first reschedule is free, and any fee for later attempts must be stated on the listing. Operation attempted and not possible for reasons on our side, or the platform/vehicle combination proves unsupported despite meeting the listing requirements: full refund. Operation completed as described: the price is earned and non-refundable. This section does not limit your statutory rights or rights under card-network rules.

8. WARRANTY

If an operation we completed proves faulty — the write did not take correctly, or coding we applied is wrong — contact us: we re-connect and correct our work at no charge. The warranty covers our operation; it does not cover vehicle-side faults, later changes by others, or new unrelated failures.

9. LAWFUL USE

Sessions are for lawful repair, replacement, and configuration of vehicles you own or are authorized to service. We do not perform emissions-control alterations or deletions, and we do not perform odometer alteration.

10. PAYMENT AND BILLING DESCRIPTOR

Payment is processed by Square on behalf of DLP Mobile Services LLC (doing business as Auto Module Lab). Your card statement may show DLP Mobile Services LLC or Auto Module Lab.

11. IF SOMETHING GOES WRONG; ELECTRONIC SIGNATURE

Contact us first at the email or phone number on your order confirmation and give us a reasonable opportunity to make it right. Nothing in these Terms waives rights you have under card-network rules or consumer-protection law. These Terms are governed by Texas law; venue lies in Tarrant County, Texas, except where applicable law requires otherwise. Checking the acceptance box and typing your name at checkout constitutes your electronic signature under the U.S. E-SIGN Act and the Texas Uniform Electronic Transactions Act, and we record the accepted version, time, IP address, and browser identifier as evidence of the agreement.

Outside the US? Include your country code.

Pick a day to see open times (Central Time) — or skip it and we’ll schedule with you.

Openings come straight from our live calendar. Skip it and we'll text you a link to pick your time after payment.

Secure Square checkout · refunded if the supported procedure can't be completed

Vehicle, module and OEM-software compatibility varies. OEM subscriptions, security credentials and manufacturer fees may be required and are not included unless expressly stated. Confirm compatibility with Auto Module Lab before beginning a programming procedure. No J2534 yet? The Multi-Brand Kit ($349) and the Complete Shop Kit ($499) run this session, with the interface, setup, and this session bundled into one checkout.