Volkswagen · Mk5 (A5 platform) · 2006–2009
Rabbit / GTI / R32 2006–2009 engine ECU part numbers
5 engines, 5 ECU part-number families. Find the controller your car runs, then clone it onto a donor or adapt it remotely.
Engines and their ECUs
| Engine | Engine codes | ECU family | Part-number prefix |
|---|---|---|---|
| 2.5 five-cylinder | BGP, BGQ, BPR, BPS | Bosch ME7.1.1 | |
| 2.5 five-cylinder (2009) | CBTA, CBUA | Bosch ME17.5 | |
| 2.0T FSI (GTI) | BPY | Bosch MED9.1 | |
| 2.0 TSI (GTI, 2009) | CCTA, CBFA | Bosch MED17.5 | |
| 3.2 VR6 (R32, 2008) | BUB | Bosch ME7.1.1 |
The Mk5 MED9.1 (1K0 907 115) is the VW ECU most often cloned because it failed — see the clone service page for the no-start pattern.
The part-number prefix is the family-level part of the label (for example 06J 906 026 CK). A donor must match the full number, which we confirm against your VIN for free before you buy.
Clone the Rabbit / GTI / R32 ECU — $350 flat
Mail your original and a donor with the same full part number. VIN, immobilizer data, coding and adaptations are copied across on the bench, typically within 24 hours of arrival. Factory immobilizer stays on.
Volkswagen engine ECU cloneOn-car software step — remote ODIS, $250
Some cars still want an on-car step after a module swap: a software version management (SVM) update, coding, or a basic-settings adaptation. Plug a J2534 pass-thru interface into the car and we run the factory ODIS software on it from our bench — no dealer visit. The same session covers coding after any other VW or Audi module replacement.
Book the VW / Audi remote sessionFrequently asked questions
Which engine ECU does a 2006–2009 Rabbit / GTI / R32 have?
It depends on the engine. The 2.5 five-cylinder (BGP, BGQ, BPR, BPS) runs Bosch ME7.1.1, part-number prefix 07K 906 032. The 2.5 five-cylinder (2009) (CBTA, CBUA) runs Bosch ME17.5, part-number prefix 07K 906 055. The 2.0T FSI (GTI) (BPY) runs Bosch MED9.1, part-number prefix 1K0 907 115. The 2.0 TSI (GTI, 2009) (CCTA, CBFA) runs Bosch MED17.5, part-number prefix 06J 906 026 or 1K0 907 115. The 3.2 VR6 (R32, 2008) (BUB) runs Bosch ME7.1.1, part-number prefix 022 906 032. The label on your module settles it in seconds.
Can you clone the ECU on a Rabbit / GTI / R32 Mk5 (A5 platform)?
Yes — every engine ECU on this generation is a routine bench clone. Mail your original and a donor with the same full part number and we copy the VIN, immobilizer data, coding and adaptations across for $350 flat, typically within 24 hours of arrival.
Will a cloned Rabbit / GTI / R32 ECU need dealer adaptation?
Usually not — it leaves the bench carrying your VIN, immobilizer data, coding and adaptations. If the car still asks for an on-car step, we run it remotely with ODIS over your J2534 interface for $250.