
Chrysler, Dodge, Jeep Sentry Key (SKIM) by Model, 1998-2010
The short answer: SKIM is the column ring on 1998-2007 vehicles
The Sentry Key Immobilizer Module (SKIM) is a small module mounted on the steering column, and its plastic antenna ring circles the ignition lock cylinder. It is the security brain of the Sentry Key system that Chrysler used on many of its vehicles from 1998. The SKIM stores the vehicle's security PIN and the list of keys the vehicle will accept, and it talks to the engine computer to permit the engine to run.
Not every Chrysler, Dodge or Jeep of that era has one, and not every later vehicle that looks similar uses the same system. This guide answers one practical question: does my vehicle have the column-mounted SKIM, and if so, what are my options? It is built from our own service catalog, which lists the covered models and, just as usefully, the vehicles it does not cover.
Pricing note: every dollar figure for our services below is read from our own service catalog. Model and year ranges are the ones on our service pages, and "when equipped" means some vehicles in that range were built without the system.
What the SKIM does, and why the PIN matters
The Sentry Key system works through a handshake. When you turn the key, the antenna ring around the ignition powers and reads the transponder in the key head. The SKIM checks the key's code against its list. If the key is accepted, the SKIM tells the engine computer that the vehicle may run. If it is not accepted, the engine computer may start the engine and then shut it down, which is why a Sentry Key vehicle with a wrong key often starts and dies within about two seconds, with the security light flashing.
The module also holds a four-digit security PIN. That PIN is the gatekeeper for adding keys. On the 1998 to 2004 vehicles, the PIN is not sent on the vehicle's data bus, so no scan tool can read it through the OBD port. The dealer can need the vehicle and a code lookup that often no longer exists for a car this old. Reading the SKIM directly on the bench is the path that does not depend on a code lookup.
That is the technical reason a mail-in service exists for these vehicles. We do not need the whole vehicle. We need the SKIM and, if you have no cut key, the driver's door lock cylinder. We read the module on the bench, program a fresh transponder key and return everything in one box.
How to tell whether your vehicle has a SKIM
You can usually decide in two minutes with the dash and the key. Look for these four signs, which come straight from our service pages:
- A plastic ring around the ignition lock cylinder under the column shroud.
- An amber key-shaped light in the cluster that glows for about three seconds at key-on.
- A grey rubber cap on the head of the original key, the Sentry Key.
- The security light flashing while the engine dies about two seconds after starting, when an unrecognized key is used.
If you see the ring and the amber light, you almost certainly have the column-mounted SKIM. If the key has the remote buttons built into the head and the vehicle is a 2006 or newer, you are probably looking at a different system, and the sections below explain how to tell.
The model list: which vehicles use the column-mounted SKIM
The list below is the coverage stated on our service pages. "When equipped" means a given year of a model was sold both with and without the system.
Jeep
- Grand Cherokee WJ, 1999 to 2004
- Liberty KJ, 2002 to 2007
- Wrangler TJ and LJ, 2003 to 2006, when equipped, because some were built without it
- Cherokee XJ, 1998 to 2001, when equipped
Dodge and Plymouth
- Intrepid, 1998 to 2004
- Neon and Neon SRT-4, 2000 to 2005
- Stratus sedan, 2001 to 2006, but not the Mitsubishi-built coupe
- Caravan, Grand Caravan and Plymouth Voyager, 2001 to 2007
- Dakota, 2001 to 2004
- Durango, 2001 to 2003
- Ram 1500, 2500 and 3500, 2002 to 2005, when equipped with the Sentry Key
Chrysler
- Concorde, LHS and 300M, 1998 to 2004
- Sebring sedan and convertible, 2001 to 2006, but not the Mitsubishi-built coupe
- PT Cruiser, 2001 to 2010
- Town and Country and Voyager, 2001 to 2007
- Pacifica, 2004 to 2008
Later trucks where the module still sits on the column
- Dakota, 2005 to 2007
- Durango, 2004 to 2007
- Chrysler Aspen, 2007
For those later trucks, our service page says to text a photo first, because identification is less clear-cut than on the earlier vehicles.
The vehicles that look similar but are not SKIM
This is where most ordering mistakes happen, so it deserves its own section. Several popular models fall outside the column-mounted SKIM, and each uses a different system that cannot be handled by shipping a column module.
- 2005 and newer Chrysler 300, Dodge Charger and Magnum, Jeep Grand Cherokee WK and Commander. These use SKREEM, not SKIM, with the remote built into the key. From 2005 to 2007 Chrysler moved to the SKREEM and WCM, according to our service page.
- Ram 2006 to 2008. The Ram moved to the SKREEM and WCM system from 2006.
- Every 2008 and newer vehicle with the fob built into the key. These use WIN, the Wireless Ignition Node, with FOBIK keys. They are different systems that need the vehicle.
- Sebring and Stratus coupes. These were built by Mitsubishi and carry a Mitsubishi immobilizer.
- Chrysler Crossfire. Its SKREEM sits behind the cluster, and it has its own service. See our Crossfire key service and Crossfire key replacement guide.
If your vehicle is in one of these groups, the SKIM options below do not apply. If you are unsure, text a photo of the ring and the year and model before ordering.
The comparison table: model, system and what fits
The table pulls the main cases together so you can find your vehicle in one place.
| Vehicle | Years | Immobilizer system | Bench option that fits |
|---|---|---|---|
| Jeep Grand Cherokee WJ | 1999-2004 | Column SKIM | SKIM key, $125 or $150 |
| Jeep Liberty KJ | 2002-2007 | Column SKIM | SKIM key, $125 or $150 |
| Jeep Wrangler TJ and LJ | 2003-2006, when equipped | Column SKIM | SKIM key, $125 or $150 |
| Dodge Neon and SRT-4 | 2000-2005 | Column SKIM | SKIM key, $125 or $150 |
| Dodge and Chrysler minivans | 2001-2007 | Column SKIM | SKIM key, $125 or $150 |
| Ram 1500, 2500, 3500 | 2002-2005, when equipped | Column SKIM | SKIM key, $125 or $150 |
| PT Cruiser | 2001-2010 | Column SKIM | SKIM key, $125 or $150 |
| Chrysler 300 and Dodge Charger | 2005+ | SKREEM | Not this service; text first |
| Jeep Grand Cherokee WK and Commander | 2005+ | SKREEM | Not this service; text first |
| Ram | 2006-2008 | SKREEM and WCM | Not this service; text first |
| Any vehicle with the fob in the key | 2008+ | WIN with FOBIK | Not this service; text first |
| Sebring and Stratus coupes | Mitsubishi-built | Mitsubishi immobilizer | Not this service |
The two bench options, and which one you need
Once you know you have a SKIM, the choice is between two flat-price services, and the deciding question is simple: do you have a key that turns the door?
Transponder-only key, $125. You ship the SKIM and any existing keys. We read the module, program a fresh transponder and return the module with the key. The blade arrives uncut, so any locksmith can cut it from an existing key or from your lock. The key starts the engine but has no remote lock and unlock buttons, because it is a valet-style key. All keys lost is included.
Cut and programmed key, $150. You ship the SKIM and your driver's door lock cylinder. We decode the lock, cut the blade to match and program the transponder. You get back a key that turns the locks and starts the engine, plus your SKIM, your lock and any old keys in one return box. Most of these vehicles have no key code on file anywhere, so the cut exists only inside your locks. Send the driver's door lock, not the ignition: it is the easiest to remove, and on these vehicles the door and ignition are cut to the same code.
Return shipping is paid by you at checkout, starting from $29.95. We buy and email the prepaid inbound label. A standard-return transponder-only job is therefore $154.95, and a standard-return cut and programmed job is $179.95. UPS 2-Day is $54.95 and UPS overnight is $94.95; exactly one tier is charged per order. For how the pieces add up across services, our worked examples of total mail-in cost with shipping shows more totals, and our mail-in key programming cost guide puts these two options next to the BMW, Mercedes, Volvo and Subaru key prices.
The scenarios we see most
All keys lost on a Grand Cherokee WJ or Liberty. There is nothing to copy a blade from and no dealer PIN. The cut and programmed option at $150 fits, with the SKIM and the driver's door lock cylinder in the box.
A used Jeep, Ram or Dakota bought with one key or none. A buyer with one key should get a second made before the first one fails. A buyer with no keys needs the cut and programmed option.
A cut key that turns the door and the ignition, but the engine dies in two seconds with the security light flashing. The mechanical key is right and the electronic registration is wrong. The transponder-only option at $125 fits, because you only need the SKIM and the blade can be copied from your cut key.
A replaced SKIM. If a broken SKIM was replaced with a used one, a key has to be paired to it. Same options apply.
A plain spare for the drawer. The transponder-only option is also the cheapest way to get a second key without a dealer visit.
For the broader question of whether the key or the module is at fault, our guide on a car that starts with the spare key but not the main key gives a driveway test sequence.
SKIM versus the engine computer: two separate jobs
Owners sometimes confuse the SKIM key service with the PCM-side work, which is a different product.
The SKIM is the security module on the column. The PCM is the engine computer, and on Sentry Key vehicles it must agree with the SKIM about the security data. If the PCM was replaced with a used one, it can be locked to another vehicle's secret key. That is a different problem with a different fix, and our guide to Chrysler PCM and SKIM replacement and our Sentry Key PCM-side guide cover it.
There is also a deliberate immobilizer-delete service on the PCM. It removes the Sentry Key security routine inside the engine computer so it no longer looks for a transponder challenge, and it is $250 flat on SBEC3, SBEC3A, JTEC and NGC-based PCMs. Our service page frames it for engine swaps, salvage controllers, a deleted or missing SKIM, and lost-key situations where the SKIM cannot be re-married. It is a repair and swap tool, offered for use where it is legal, and it does not change the stored VIN or touch emissions calibration. It requires proof of ownership like every key and immobilizer job.
If your problem is that a swapped or salvage PCM is locked to another car, the delete may fit. If your problem is simply that you have no key, the SKIM key options above are the right ones, and they leave the original security system intact.
Why the age of these vehicles shapes the decision
The vehicles in this guide are old. S&P Global Mobility reports that the average US light vehicle reached 12.8 years old in 2025, with passenger cars averaging 14.5 years and light trucks 11.9 years, across about 289 million light vehicles in operation. A 1999 Grand Cherokee or a 2004 Caravan is well above those averages, which means many are worth less than a dealer-scale solution would cost, and that is exactly the situation a flat $125 to $150 bench job is built for.
Check the vehicle's market value before spending anything, with Kelley Blue Book or by reading model-specific ownership coverage from Car and Driver and MotorTrend. For older vehicles, Hagerty is a useful reference. A key job that costs a few hundred dollars all in is proportionate to a 15-year-old Jeep in a way a four-figure dealer path often is not.
"The mistake I see most is people assuming a 2006 or 2007 vehicle is the same system as a 2004. Chrysler changed immobilizers mid-decade and the model name did not change with it. Check for the ring on the column before you order anything." — Independent Chrysler immobilizer technician, 15+ years on Sentry Key and SKREEM systems (anonymized)
Proof of ownership, legal framing and security
Key and immobilizer work requires proof of ownership. We need registration or title in your name and a VIN that matches the vehicle. Our proof of ownership guide lists what is accepted. Immobilizer-delete work is offered for legitimate repair, engine swap, off-road and orphaned-platform situations, where it is legal.
The reason is theft. The National Insurance Crime Bureau, as reported by Insurance Journal, counted 659,880 vehicles reported stolen nationwide in 2025. For background on theft prevention, see the NICB. A bench service that can program a key without the vehicle must verify who is asking, and we do.
How to remove and ship the SKIM
- Disconnect the battery before you touch anything.
- Remove the upper and lower column shrouds. The SKIM unplugs from the steering column once the shrouds are off.
- Unplug its connector. The ring is part of the module and comes off as one piece. The ignition lock itself stays in the vehicle.
- If you ordered the cut and programmed key, remove the driver's door lock cylinder as well.
- Pack it static-safe with padding, and include any existing keys, working or not.
- Include your order confirmation, your VIN, year and model, proof of ownership and your return address.
Our guide to removing and shipping a car module covers static protection, and what to ship by job type lists the box contents. The mail-in address is a PO Box for USPS and an Oakwood Lane suite address for UPS and FedEx, because UPS and FedEx cannot deliver to a PO Box; both lines are on the service page and in the order email.
Sources and further reading
For recall lookups, use NHTSA. For vehicle security and safety research, see the Insurance Institute for Highway Safety and SAE International. For a map of the modules involved, our guide to every control module in a modern car is a good starting point.
Frequently asked questions
Which Chrysler, Dodge and Jeep models have the column-mounted SKIM?
Mainly 1998 to 2007 vehicles including the Grand Cherokee WJ, Liberty KJ, Neon, Intrepid, Caravan and Town and Country, PT Cruiser through 2010, Dakota, Durango and the 2002 to 2005 Ram when equipped. Some Wrangler TJ and Cherokee XJ years were built without it.
How do I know if my vehicle has a SKIM?
Look for a plastic ring around the ignition lock cylinder under the column shroud, an amber key-shaped light in the cluster that glows for about three seconds at key-on, and a grey rubber cap on the key head. A security light that flashes as the engine dies after about two seconds is another sign.
What is the difference between SKIM, SKREEM and WIN?
SKIM is the column-mounted Sentry Key module of 1998 to 2007 vehicles. SKREEM is the later unit used on the 2005 and newer 300, Charger, Magnum, WK Grand Cherokee and Commander, with the remote built into the key. WIN is the Wireless Ignition Node used from 2008 with FOBIK keys. Only SKIM is covered by the $125 and $150 options.
How much does a Sentry Key replacement cost by mail?
As of November 2026, a transponder-only key is $125 and a cut and programmed key is $150, both flat. Return shipping is extra, starting from $29.95, so standard-return totals are $154.95 and $179.95. We buy and email the prepaid inbound label.
Why can't the PIN be read through the OBD port?
On 1998 to 2004 vehicles the PIN is stored in the SKIM and never sent on the data bus, so no scan tool can read it through the OBD port. Reading the module directly on the bench is the path, which is why we ask you to ship the SKIM.
Do my existing keys keep working?
Yes. We add the new transponder to the SKIM, and keys that work today keep working. If you want a lost key removed so it can never start the vehicle, say so on the order note and we will drop it.
Do I need to send the door lock?
Only if you have no cut key. If you have a key that turns the door, order the $125 transponder-only option and have the blade copied locally. If you have no key at all, order the $150 option and ship the driver's door lock cylinder so we can decode it and cut the blade.
The bottom line
The Sentry Key SKIM is the column ring on most 1998 to 2007 Chrysler, Dodge and Jeep vehicles, and identifying it correctly is the first and most important step. Look for the ring, the amber key light and the grey-capped key. Models such as the Grand Cherokee WJ, Liberty, Neon, Caravan and PT Cruiser use it, and the 2005 and newer 300, Charger, Magnum, WK Grand Cherokee and Commander, the 2006 Ram and every 2008 and newer WIN vehicle do not. For the vehicles that do, as of November 2026 the bench options are $125 for a transponder-only key and $150 for a cut and programmed key, plus return shipping from $29.95. Check your model against the table, text a photo when you are unsure, and ship the module with proof of ownership.
Ship it for the chrysler / dodge / jeep skim transponder key (uncut) — $125 flat
Typical 24-Hour Bench Turnaround, return speed your choice at checkout. Prepaid inbound label by email the minute you order.
More from the Lab

Chrysler, Dodge & Jeep PCM Replacement
10 min · July 13, 2026

Chrysler SKIM / Sentry Key Delete Guide (2026 Mail-In)
12 min · June 18, 2026

Car Key Programming Cost — Mail-In Bench Programming (2026)
15 min · November 16, 2026

Car Starts With Spare Key, Not Main Key: Key or Module?
12 min · November 16, 2026